1
1
030-06029-603
適合機種
本オプションは 、以下の機種に適合しています。
内容物リスト
このパッケージには、以下のもの が 入っ ています 。
排紙台 W 設置手順書
1. 排紙台W ............................................... 1台
2. 排紙台サポート組 立;F .......................... 1枚
3. 排紙台サポート組 立;R ......................... 1枚
4. 排紙台W支え;F ................................... 1個
5. 排紙台W支え;R ................................... 1個
6. 排紙台Wアダプタ;前 ............................ 1個
7. 排紙台Wアダプタ;後 ............................ 1個
8. 吸着板W ............................................... 1枚
9. 排紙台スペーサ .................................... 2枚
10. 取付ネジ................................................. 1式
11. 説明シール ............................................1枚
12. シール2種類(海外用)........................ 各1枚
13. 設置手順書(本書).............................. 1冊
1. 電源を切り、電源コードを印 刷 機 から抜き取る。
2. 印刷機に標準排紙台がついている場合は、排紙台
外れ防止金具を取り外 して 排 紙 台を外 し 、排紙台
支え;F 、Rも取り外す。
排紙台支え;F
ORPHIS Xシリーズ
RISOGRAPH RZ4/6、RZ7/9、RE-Zシリーズ
RISOGRAPH MZ7/9、MX7、RE-Mシリーズ
リソグ ラフ RP3シリーズ(RP359, RP379を除く)
SPEDIO RX3シリーズ(RX3590, RX3790を除く)
RISO RP3シリーズ(RP3590, RP3790を除く)
排紙台支え;R
排紙台 W
排紙台 W 支え;F
排紙台 W 支え;R
排紙台外れ防止金具
標準排紙台
上からはめて
ゆっくり寝かす
3. 吸着板Wを排紙台Wに取り付ける。
(バインドM4×10 1本)
4. 排紙台スペーサを、ボスの凸 部を表 側にして排紙
台Wの両側に取り付ける。
(バインドM4×10 各1本)
5. 排紙台サポート組 立;F 、Rを排紙台Wに取り付け
る。(バインドM4×10 各2本)
6. 同梱の排紙台W支え;F 、Rを、手順2で外したネ
ジで印刷機に取り付ける。
7. 排紙台Wを排紙台W支えに上からはめ込んで、
手順2で外した排紙台外れ防止金具で固定する。
排紙台スペーサ排紙台サポート組立;F
排紙台サポート組立;R
吸着板 W
RZ4/6
、
RZ7/9
、
MZ7/9
、
RE-M
、
RE-Z
、
RX6
、
RX7
、
MX7 シリーズに設置するには、以下のサービス
パーツが必要です。
・排紙台 W 支え組立; 前(045-22551)
・排紙台 W 支え組立; 後(045-22552)
〈RP3 シリーズ、RX3 シリーズの場合〉
排紙台外れ防止金具
本機の設置は、必ず専門の技術者が行って
ください。
ORPHIS X シリーズに設置するには、排紙オプ
ション接続キットが必要です。
Wide Stacking Tray Installation Procedure
RISO KAGAKU CORPORATION Models
SE series
RISO EZ2/3/5, EV2/3/5 series
RISO MZ7/9, MV7 series
RISO RZ9, RV9 series
RISO RP3700, RP3500, RP3100
1. Wide stacking tray ............................................ 1 unit
2. Wide stacking tray arm F .................................. 1 pc.
3. Wide stacking tray arm R ................................. 1 pc.
4. Wide stacking tray support F ............................ 1 pc.
5. Wide stacking tray support R ............................ 1 pc.
6. Wide stacking tray adaptor F ............................ 1 pc.
7. Wide stacking tray adaptor R ............................ 1 pc.
8. Tray catcher plate .............................................. 1 pc.
9. Stacking tray arm spacer ................................... 2 pcs.
10. Screws ............................................................... 1 set
11. Explanation label ............................................. 1 pc.
12. Instruction label (2 types) ........................... 1 pc. each
13. Installation guide (This manual) ................. 1 copy
Types of Applicable Printers
The following printer models are the intended
basic units for installing the Wide Stacking Tray.
Packing List
This package contains the following items.
1. Turn off the power switch of the printer and unplug
the power cord.
2. Remove both the standard Paper stacking tray and
the Stacking tray supports by removing the
Stacking tray arm locks.
6. Secure the Wide stacking tray support F and R with
the screws removed in the step 2.
7. Fit the Wide stacking tray in the Wide stacking
tray supports from above and secure it with the
Stacking tray arm locks removed in the step 2.
8. Stick the Instruction labels on the Paper receiving
tray and the Paper stop respectively so that each
label covers the previously affixed ones.
Standard paper stacking tray supports
Stacking tray arm locks
Wide stacking tray support R
Stacking tray arm locks
Insert the joint from above
and gently lower the other
end.
Wide stacking tray arm F
Wide stacking tray arm R
Stacking tray arm spacer
3. Secure the Tray catcher plate to the Wide stacking
tray. (Binding screw M4x10, 1 pc)
4. Secure the Stacking tray arm spacers to the tray
with the embossed sides facing up.
(Binding screw M4x10, 2 pcs)
5. Secure the Wide stacking tray arm F and R to the
Wide stacking tray. (Binding screw M4x10, 4 pcs)
Tray catcher plate
When installing on EZ2/3/5, EV2/3/5, MZ7/9,
MV7, RZ9 or RV9 series models, following
items are additionally required;
・
Wide stacking tray support; Front (045-22551)
・
Wide stacking tray support; Rear (045-22552)
Wide stacking tray support F
= For RISO RP series models =
The Paper Ejection Attachment Kit (separately
packaged) is required to install this option to the
“ComColor”
“SE series” is the model name of “ComColor”.
Nobody but Riso-authorized service
representatives is allowed to install this unit.
Kommentare zu diesen Handbüchern